|
Dimensions: |
Metric |
Imperial |
|
External Length |
12,192mm |
40ft |
|
External Width |
2,438mm |
8ft |
|
External Height |
2,896mm |
9ft6" |
|
Internal Length |
11,590mm |
456.30" |
|
Internal Width |
2,294mm |
90.31" |
|
Internal Height |
2,557mm |
100.67" |
|
Door Opening Width |
2,290mm |
90.16" |
|
Door Opening Height |
2,596mm |
102.20" |
|
Cubic Capacity |
67.9m3 |
2,398ft3 |
|
Maximum Gross Weight |
35,000kg |
77,160lbs |
|
Tare Weight |
4,140kg |
9,130lbs |
|
Tare Weight including Machinery |
4,580kg |
10,100lbs |
|
Payload |
30,420kg |
67,060lbs |
|
Stacking Height |
9 |
|
|
Stacking Load |
216,000kg (stacking test load per post 97,200kg) |
476,200lbs |
|
Racking Test Load |
15,240kg |
33,600lbs |
|
Construction: |
||
|
Top and Bottom Rail Material |
Corten Steel |
|
|
End Frames Material |
Corten Steel |
|
|
Outer Panels |
MGSS |
|
|
Underfloor |
MGSS |
|
|
Inner Side Lining |
HGSS SUS 304 |
|
|
Tee Floor Height |
63.5mm |
|
|
Door Outer Material |
MGSS |
|
|
Lock Rods |
4 |
|
|
Goose Neck Tunnel Length |
3,174mm |
|
|
Goose Neck Tunnel Width |
1,029mm |
|
|
Goose Neck Tunnel Height |
120mm |
|
|
Fork Lift Pockets |
None |
|
|
Side Insulation |
Thickness: 60mm Density: 50kg/m3 |
|
|
Floor Insulation |
Thickness: 135/76mm Density: 65kg/m3 |
|
|
Roof Insulation |
Thickness: 80mm Density: 40kg/m3 |
|
|
Door Insulation |
Thickness: 74mm Density: 55kg/m3 |
|
|
Air Leakage |
2.0m3/hr |
|
|
Heat Leakage |
35kcal/hr/°C |
|
|
Door Sill |
MGSS |
|
|
Floor Rail |
63.5mm high extruded aluminum "T" shape section |
|
|
Floor Stringer |
Extruded aluminum omega shaped profiles will be step-welded to the T-floor (Quantity: 9) |
|
|
Scuff Liner |
Aluminum |
|
|
Door Holder |
A SUS 304 wire with plastic outside is provided on each door |
|
|
Door Gasket Outer |
E.P.D.M. "C"&"O" section double lips |
|
|
Side Post and Stringers |
Outer: 4.5mm middle hat shape Corten A glued or spot welded to side panel, 8 each side 0.8mm MGSS or 1.6 mm Corten hat shape spot-welded to side panel Inner: 0.8mm hat shape MGSS spot-welded (Quantity: 8 each side) |
|
|
Roof Bow and Stringer |
Outer: 0.8mm MGSS pressed plates spot-welded to roof panel (6 pieces) Inner: 0.8mm thick aluminum stringer affixed to the roof lining by glue and rivets (7 pieces) |
|
|
Roof Lining |
0.8mm thick one piece of pre-painted white aluminum sheet with small corrugations |
|
|
Paint Corten Steel Parts |
1st primer: Hot spray galvanized: DFT 30 Micron 2nd primer: Epoxy zinc phosphated: DFT 50 Micron 3rd top: Acrylic top coat: DFT 70 Micron Top coat colour: RAL 9010 (White) Total DFT: 150 Micron |
|
|
Paint MGSS Parts |
1st primer: Epoxy zinc phosphated: DFT 50 Micron 2nd top: Acrylic top coat: DFT 70 Micron Top coat colour: RAL 9010 (White) Total DFT: 120 Microns |
|
|
Paint Under Structure |
1st primer: Hot spray galvanized (only for Corten frame): DFT 30 Micron 2nd primer: Epoxy zinc phosphated: DFT 50 Micron 3rd top: Tectyl 121B or Dinitrol 4941K: 200 Micron Total DFT: 250/280 Micron |
|
|
Top Coat Colour |
RAL 9010 (White) |
|
|
Top and Bottom Lifting Test |
2.3 R-T |
|
Actual measurements and specifications may vary and are subject to confirmation.